Go to MPEP - Table of Contents
608.02(e) Examiner Determines Completeness and Consistency of Drawings [R-2] - 600 Parts, Form, and Content of Application
608.02(e) Examiner Determines Completeness and Consistency of Drawings [R-2]
The examiner should see to it that the figures are correctly described in the brief description of the several views of the drawing section of the specification, that the reference characters are properly applied, that no single reference character is used for two different parts or for a given part and a modification of such part, and that there are no superfluous illustrations.
One or more of the following form paragraphs may be used to require correction.
**>¶ 6.22.02 Drawings Objected to, Different Numbers Refer to Same Part
The drawings are objected to as failing to comply with 37 CFR 1.84(p)(4) because reference characters "[1]" and "[2]" have both been used to designate [3]. Corrected drawing sheets are required in reply to the Office action to avoid abandonment of the application. Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The replacement sheet(s) should be labeled Replacement Sheet in the page header (as per 37 CFR 1.84(c)) so as not to obstruct any portion of the drawing figures. If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action. The objection to the drawings will not be held in abeyance.
Examiner Note
1. In brackets 1 and 2, identify the numbers which refer to the same part.
2. In bracket 3, identify the part which is referred to by different numbers.
3. Unless applicant is otherwise notified in an Office action, objections to the drawings in a utility or plant application will not be held in abeyance, and a request to hold objections to the drawings in abeyance will not be considered a bona fide attempt to advance the application to final action. See 37 CFR 1.85(a).
4. This form paragraph may be followed by form paragraph 6.27 to require a marked up copy of the amended drawing figure(s) including annotations indicating the changes made in the corrected drawings.
¶ 6.22.03 Drawings Objected to, Different Parts Referred to by Same Number
The drawings are objected to as failing to comply with 37 CFR 1.84(p)(4) because reference character "[1]" has been used to designate both [2] and [3]. Corrected drawing sheets are required in reply to the Office action to avoid abandonment of the application. Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The replacement sheet(s) should be labeled Replacement Sheet in the page header (as per 37 CFR 1.84(c)) so as not to obstruct any portion of the drawing figures. If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action.The objection to the drawings will not be held in abeyance.
Examiner Note
1. In bracket 1, identify the number which refers to the different parts.
2. In brackets 2 and 3, identify the parts which are referred to by the same number.
3. Unless applicant is otherwise notified in an Office action, objections to the drawings in a utility or plant application will not be held in abeyance, and a request to hold objections to the drawings in abeyance will not be considered a bona fide attempt to advance the application to final action. See 37 CFR 1.85(a).
4. This form paragraph may be followed by form paragraph 6.27 to require a marked up copy of the amended drawing figure(s) including annotations indicating the changes made in the corrected drawings.
¶ 6.22.06 Drawings Objected to, Reference Numbers Not in Drawings
The drawings are objected to as failing to comply with 37 CFR 1.84(p)(5) because they do not include the following reference sign(s) mentioned in the description: [1]. Corrected drawing sheets are required in reply to the Office action to avoid abandonment of the application. Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The replacement sheet(s) should be labeled Replacement Sheet in the page header (as per 37 CFR 1.84(c)) so as not to obstruct any portion of the drawing figures. If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action.The objection to the drawings will not be held in abeyance.
Examiner Note
1. In bracket 1, specify the reference characters which are not found in the drawings, including the page and line number where they first occur in the specification.
2. This form paragraph may be modified to require or allow the applicant to delete the reference character(s) from the description instead of adding them to the drawing(s).
3. Unless applicant is otherwise notified in an Office action, objections to the drawings in a utility or plant application will not be held in abeyance, and a request to hold objections to the drawings in abeyance will not be considered a bona fide attempt to advance the application to final action. See 37 CFR 1.85(a).
4. This form paragraph may be followed by form paragraph 6.27 to require a marked up copy of the amended drawing figure(s) including annotations indicating the changes made in the corrected drawings.
¶ 6.22.07 Drawings Objected to, Reference Numbers Not in Specification
The drawings are objected to as failing to comply with 37 CFR 1.84(p)(5) because they include the following reference character(s) not mentioned in the description: [1]. Corrected drawing sheets, or amendment to the specification to add the reference character(s) in the description are required in reply to the Office action to avoid abandonment of the application. Any amended replacement drawing sheet should include all of the figures appearing on the immediate prior version of the sheet, even if only one figure is being amended. The replacement sheet(s) should be labeled Replacement Sheet in the page header (as per 37 CFR 1.84(c)) so as not to obstruct any portion of the drawing figures. If the changes are not accepted by the examiner, the applicant will be notified and informed of any required corrective action in the next Office action. The objection to the drawings will not be held in abeyance.
Examiner Note
1. In bracket 1, specify the reference characters which are not found in the specification, including the figure in which they occur.
2. Unless applicant is otherwise notified in an Office action, objections to the drawings in a utility or plant application will not be held in abeyance, and a request to hold objections to the drawings in abeyance will not be considered a bona fide attempt to advance the application to final action. See 37 CFR 1.85(a).
3. This form paragraph may be followed by form paragraph 6.27 to require a marked up copy of the amended drawing figure(s) including annotations indicating the changes made in the corrected drawings.
<
Go to MPEP - Table of Contents